How you can Do a Macbook Screen Replacement of a LCD Display screen
Right here is how one can save your self some money and time by replacing the LCD display screen in your Macbook laptop yourself.
Unlock the battery to remove it. Around the front of the screen is a plastic bezel, launch the clips which are holding it and take away it. If there are any clips with the bezel, pry them up with a flat blade screwdriver to remove them. Install those clips again into the LCD frame. Remove the three 4.5mm screws that secure the hinges and the 12 4.5mm screws that hold the LCD brackets to the rear housing. Depart the screws in the prime corners. Take away the brackets and the LCD from the rear housing. The realm by the iSight camera needs to be bent again slightly.
Place the LCD face down on the keyboard. Remove the tape and the iSight cable that secures the video connector and slide the cable out to the bottom of the screen. Free the tape that holds the cable assembly to the again of the LCD and transfer it aside. Take away the three 3mm screws on each side and the three on the top that hold the mounting brackets to the LCD. Carry the brackets up and move them out of the way. Pull two inverter cables that are normally yellow and pink but could also be black and gray or white and pink firmly to the proper to release the inverter cable from the inverter board. Move the outdated LCD panel out of the way.
Remove the 2 6mm screws on the short aspect of the battery housing. Leave the 3 captive screws on the memory cover bracket free and remove the bracket. Remove the three screws that hold the palm rest/keyboard to the underside case. The best screw is 4.5mm and the left and center screws are 3mm. Remove the 3 screws on the bottom. The rear 2 screws are 14mm and the center screws are 11mm. Remove the two 5.5mm screws on the fitting side. The 2 screws on the left facet do not get removed. Remove the 4 screws from the back. Raise the top case and the keyboard starting within the rear. Loosen the clips which can be along the side and front. Rigorously disconnect the keyboard cable. Remove the onerous drive by sliding it out in direction of the battery housing.
Take away the two optical drive mounting screws from the hard drive housing. Disconnect the optical drive cable by prying it up gently with a nylon or plastic tool. Peel back the aluminum tape and take away the 7.5mm screw that secures the cables. Take away the 2.75mm screw that holds the optical drive. Slide the Bluetooth board to the rear and out of the bracket. Free the cable that runs between the snubber and the drive. Use the optical drive flex cable to drag and thoroughly tilt the optical drive up.
Remove the two 3mm screws in the subwoofer speaker meeting and move it towards the front. Remove three screws that maintain the optical drive bracket in place. Remove the optical drive bracket. Take away the 3mm ground screw that holds the LVDS cable. Disconnect the three antenna cables. Raise straight up to disconnect the inverter cable. Take away the hinge bracket by eradicating the three screws in the left hinge bracket. Lay the LCD housing flat in your workspace.
Reassemble by doing the method in reverse.
How you can Do a Macbook Screen Replacement of a LCD Display screen
Right here is how one can save your self some money and time by replacing the LCD display screen in your Macbook laptop yourself.
Unlock the battery to remove it. Around the front of the screen is a plastic bezel, launch the clips which are holding it and take away it. If there are any clips with the bezel, pry them up with a flat blade screwdriver to remove them. Install those clips again into the LCD frame. Remove the three 4.5mm screws that secure the hinges and the 12 4.5mm screws that hold the LCD brackets to the rear housing. Depart the screws in the prime corners. Take away the brackets and the LCD from the rear housing. The realm by the iSight camera needs to be bent again slightly.
Place the LCD face down on the keyboard. Remove the tape and the iSight cable that secures the video connector and slide the cable out to the bottom of the screen. Free the tape that holds the cable assembly to the again of the LCD and transfer it aside. Take away the three 3mm screws on each side and the three on the top that hold the mounting brackets to the LCD. Carry the brackets up and move them out of the way. Pull two inverter cables that are normally yellow and pink but could also be black and gray or white and pink firmly to the proper to release the inverter cable from the inverter board. Move the outdated LCD panel out of the way.
Remove the 2 6mm screws on the short aspect of the battery housing. Leave the 3 captive screws on the memory cover bracket free and remove the bracket. Remove the three screws that hold the palm rest/keyboard to the underside case. The best screw is 4.5mm and the left and center screws are 3mm. Remove the 3 screws on the bottom. The rear 2 screws are 14mm and the center screws are 11mm. Remove the two 5.5mm screws on the fitting side. The 2 screws on the left facet do not get removed. Remove the 4 screws from the back. Raise the top case and the keyboard starting within the rear. Loosen the clips which can be along the side and front. Rigorously disconnect the keyboard cable. Remove the onerous drive by sliding it out in direction of the battery housing.
Take away the two optical drive mounting screws from the hard drive housing. Disconnect the optical drive cable by prying it up gently with a nylon or plastic tool. Peel back the aluminum tape and take away the 7.5mm screw that secures the cables. Take away the 2.75mm screw that holds the optical drive. Slide the Bluetooth board to the rear and out of the bracket. Free the cable that runs between the snubber and the drive. Use the optical drive flex cable to drag and thoroughly tilt the optical drive up.
Remove the two 3mm screws in the subwoofer speaker meeting and move it towards the front. Remove three screws that maintain the optical drive bracket in place. Remove the optical drive bracket. Take away the 3mm ground screw that holds the LVDS cable. Disconnect the three antenna cables. Raise straight up to disconnect the inverter cable. Take away the hinge bracket by eradicating the three screws in the left hinge bracket. Lay the LCD housing flat in your workspace.
Reassemble by doing the method in reverse.
Print this page
No comments:
Post a Comment